Flyweight PA Glans Armor

[mcn]

I just finished making and am testing a very lightweight prototype device that covers the glans and requires a PA to employ.

The piece is basically just a portion of the very front cage of the Contender that I make. It's made entirely of stainless steel and uses a medium security screw to attach the PA pin to the cage.

It weighs 1-1/2 ounces, which is less than half the weight of the MouseTrap. I just put it on and will be testing it overnight to determine whether I can endure a nighttime erection. If so then I'll keep it on at least a few more days, maybe more, depending on how much I like/dislike it.

glans_shield_01.jpg

[Ihgas]

Could you fill in the bottom opening just behind the piercing? If that small area was filled in and it covered at least 3/4" back from the piercing I think it may work very well.

[mcn]

Yes, I could certainly fill in behind the piercing. I'm curious as to why though...is that a "sweet spot" for you?

[Ihgas]

Yes, with a cage like that over the head and the underside completely inaccessible for 3/4 - 1" back from the piercing, I think would be a perfect device. Light, steel, easy to clean, and covers all the right parts.

How do you have it fitting? Loose when flaccid so that you grow into it or same size as flaccid so that it squeezes when erect?

[mcn]

I made the ring with a 1-3/8" i.d, which is slightly narrower than my erect width of 1-1/2". The pin mount was welded 1/2" back from the inner, vertical bars...just enough to keep my tip touching the bars.

All specs may be adjusted to each person's requirements, and variations on this theme are entirely possible. It could be made with solid plates; or it could be made with a combination of a plate and bars.

Here's a picture of the cage of a prototype I made while designing the Contender. Just visualize it without the second base ring...the plate would cover both the top and bottom of the glans, but the sides remain open...

9332.JPG

[peter_rabbit]

Ihgas,
I also find that area behind my PA piercing is my "sweet spot". My frenum needs some stimulation for me to orgasm.

I have MCN's Contender prototype with a plate as shown above to shield my glans and frenum. I can testify that it works just great. Hungry fingers find their way to warm smooth flat steel in the middle of the night.

My cage (like MCN shows above) weighs only 64g.

MCN,
I am excited by your new flyweight offering! I have been strongly considering the MouseTrap.
I think this new glans armor weighing under 50 grams should work very well!

Decisions decisions...

[mcn]

Thanks peter_rabbit. I just added the new glans armor to my website just this morning.

I wore the piece overnight and my first night wearing it was awesome. I have a feeling I'll be wearing this device a LOT. I've never liked trapped ball devices very much, so for me this one is a real winner.

The ring is only 1/8" narrower than my erect width and the amount of compression was "just right" for me. Morning wood wasn't too intense and actually became more of a turn-on.

I'm sure if I had made the ring 1/4" narrower than my erection the amount of compression would have been a reminder not to become erect, but this wasn't what I was intending.

[Dmw13]

Oops! Didn't realize my wife had signed in last. The text below is actually from ihgas:

I have used a pa-5000 that is 1/4" thinner than my erect self and I find it to be just barely too small. It is plenty wearable so maybe it's actually just right. My only downside is peeing in the morning with morning wood. It usually doesn't go away until I pee and its a little hard to pee when I'm squeezed so tight. Other than that it's perfect. It just barely grips when I'm completely flaccid. I, too, am tempted by this device. I want steel and to have the whole head covered.

Sorry if this is too much to ask, but if I could see a picture of it on someone it would help get a feeling for the intended size. After wearing it, is there anything you would change?

[mcn]

I just posted an explicit photo of it being worn. The photo is in the Members section. Be aware it's not safe to look at the photo at work. Here's a direct link...

viewtopic.php?f=10&t=60979

[Tom Allen]

I just posted an explicit photo of it being worn. The photo is in the Members section. Be aware it's not safe to look at the photo at work. Here's a direct link...

viewtopic.php?f=10&t=60979

I accidentally deleted the post when I was editing the title to include the [Pic] tag.

Could you repost it, making sure that you pit the tag at the beginning of the post title?

Thanks.