Holy Trainer V2

[locked4now]

Has anyone had a holy trainer V2 long enough to know if the "magic locker" loosens up the longer it is used?

I was only about two weeks continual into wearing mine when I developed the ability to slip the right ball out within minutes of putting the device on. I am not sure if this is because I stretched the sack enough and had too large of ring, or if the device had loosened up around the "magic locker", but something changed and believe me it was a change you noticed right away.

I ordered the next smaller ring, but wonder if anyone else has seem similar problems with particular device.

[slave d]

MsM's HT2 that i wear 24/7 is now a couple of months old and there's no sign of any looseness. Also i can't see how any looseness in the lock could possibly cause your issue, i think you've probably needed the small ring from day one as did i !!!

d

[locked4now]

Thanks for your reply.

When I have the device locked but not on, I can move the cage up and down which changes the gap by at least 1/8". I did not try that when it was new, so not sure if that was there all along or if the metal tab on the lock wore into the resin inside the lock allowing slightly more play.

It sounds like for your experience the play was there all along, but in my initial excitement I was secure. As the excitement dropped a few notches and I stretched then the play became a problem.

I will check out the new smaller ring see if it has the same amount of play before i actually use it and compare to see if this solves the problem.

Thanks again for feedback

[fineline]

Check the lock hole in the sheath for a crack. Mine broke while I was reaching between the underside of the sheath and my scrotum to dry and apply oil. It put upward force on the sheath and the keystone of the sheath slipped out of the interlocking part on the ring, putting stress on the top around the hole. Most likely weak because the resin was still soft from the hot water in my shower. The result was a sudden relaxing of what was a pretty secure connection - very obvious.

Lesson learned - swabs only to dry and/or apply lotion under the sheath, or take it off to shower. A finger is just too fat. It's still THE most comfortable device that I have, and I bought a second one of a different color.

[locked4now]

I agree with the comfort level, and it had been very hot out here. I did look for cracks and could not actually see anything, but will double check.

Thanks for the info.

[locked4now]

Well Smaller ring came and I felt like I could barely squeeze into it. First night was tight all night and no chance of ball slipping. Took it off to clean properly the next night and put it back on, within 1 hour slipped first RH testicle out, within 10 minutes LH followed. I did place some baby gel under the balls to help with ball burn. I wonder if this extra lube contributed to the guys getting loose.

It seems like my testicles have the ability to change sizes at will.... Can't believe they both slipped through the tiny gap with smallest ring size offered. Starting to believe that I will not be able to wear the ball trap style devices.

Any thoughts or suggestions?

[Justincase]

I've got a HT v2. After a couple of weeks, the plastic cracked where the Magic Locker fits through the tube. I've been able to repair it with a piece of steel wire and some epoxy resin, but the whole design around this area is far too weak. The plastic is showing signs of wear around the area that the lock fits.
However, it is the most comfortable device I have ever used (and that's why I took the time to repair it!)

[Locked4good]

I have the HT V2 and I no signs of wear. It is very comfortable, no doubt. My two complaints (and why I just ordered a Queen's keep by mature metal) are this: 1) pain in the neck to keep good hygiene and 2) I can pull out way too easy! I even ordered the smaller (med size) ring, but that cut off circulation. Still in it now until my new device comes, but I'm on the honor system for now. Probably will end up getting the PA as that seems to be the only way to ensure security.

[slave d]

I've got a HT v2. After a couple of weeks, the plastic cracked where the Magic Locker fits through the tube. I've been able to repair it with a piece of steel wire and some epoxy resin, but the whole design around this area is far too weak. The plastic is showing signs of wear around the area that the lock fits.
However, it is the most comfortable device I have ever used (and that's why I took the time to repair it!)

Evidently they had a bad batch of resin and at least one other person has had tubes replaced under warranty with no problem. You should try, you might well get another one free if you sent pics etc !!

Cheers