My first cage. What size?

For the gearheads in the audience
Post Reply
etsu_chi
Posts: 2
Joined: Mon Sep 28, 2020 5:04 pm
Last orgasm: 5- 0- 0
Gender:

My first cage. What size?

Post by etsu_chi »

Its my first time and I want to get something to test the waters. I landed on a holy trainer knockoff but the measurements don't make much sense to me. I'm 3 1/4 inches flaccid so naturally the maxi looked ideal, but after doing some asking I was told that a small or nano would be the way to go. I don't see how a cage way smaller than my flaccid length would be comfortable.
I don't want to go as small as possible (nub) , I just want something that fits without alot of compression.
Any advice would be greatly appreciated.
Last edited by etsu_chi on Mon Sep 28, 2020 7:50 pm, edited 1 time in total.
0 x
User avatar
slave d
Posts: 1038
Joined: Mon Feb 24, 2014 9:33 pm

Re: My first cage. What size?

Post by slave d »

There’s flaccid and then there’s really flaccid !! Sit in a bath of cold water for a while until you get to “really” flaccid and then measure. You should be hitting the end ALL the time so being a little compressed is actually a good idea. You really want it so you can’t start to get an erection and most people find they end up going shorter and shorter over time as it really is better. Over the years i’ve gone down from a standard HT to a nub to now being on an even smaller s/s device. To be honest my suggestion for you would be to start with a knock off (no reason paying big money for a tester) CB6000 or similar. They come with multiple rings and everything is adjustable. That way you can play till you find what really works. Also gives you a chance to start with a bit bigger A ring and work down over time. i started in a 45mm A-ring and now have one which is under 35mm though that was over a long period !! my main elastics would be to buy cheap for a starter and something you can experiment with.

MsM’s ld
3 x
New Zealand
24/7/365 DHGate tiny s/s with hinged A-Ring
https://www.chastityforums.com/viewtopi ... =3&t=63728
User avatar
Lady M
Posts: 2236
Joined: Tue Oct 29, 2013 12:09 pm
Location: Indiana USA
Gender:
Contact:

Re: My first cage. What size?

Post by Lady M »

We are not in the get some tiny cage club... My hubby's cage fits his flaccid penis. My suggestion to guys measuring for a device is to do it over the course of a week, a couple times a day, at different times, every day of you can. This will give you a good average of where you will sit comfortably in a cage, IMO.

Personally, I wouldn't go with your shortest size... I prefer the average. The cage should fit like a glove, not be squishing your penis constantly, IMO.

I do agree you should get some knock off to try out before you actually jump in on anything expensive.

Anyway... Good luck to you!
2 x
Lady: Wife & Keyholder to cagedmonkey who is locked 24/7
Currently Wearing: Jail Bird
Owned Devices: MM Jail Bird (x2), Steelworxx Revenge
Click here for Our journey & Podcast
latentkink
Posts: 2
Joined: Mon Oct 05, 2020 1:24 pm
Gender:

Re: My first cage. What size?

Post by latentkink »

Like said above, measure several times. You want to be at the front all the time if you can. A cage that has extra room will be uncomfortable because it will allow you to get erections in the cage and that can cause pain. Contrary to what some think, fitting like a glove is the way to go. Also, it makes it easier to pee without making a mess if you fill the cage at all times. After a few days you won’t notice that you’re snug just like you don’t notice socks all day.
2 x
User avatar
Caged Lion
Posts: 41
Joined: Thu Feb 02, 2017 6:40 pm
Contact:

Re: My first cage. What size?

Post by Caged Lion »

First of all, I strongly suggest avoiding a very tight base ring. You only need one tight enough to prevent a ball from slipping out. Believe it or not, most men end up at 1 3/4" (45mm). No idea why, but that's what several manufacturers told me. I wear that size. In terms of length, it depends on the device.If it is a standard cage/tube with no glans ring (holds the glans in the front of the cage), I found shorter to be better. You want the head of your penis in firm contact with the front of the cage at all times. This makes peeing neater and avoids issues with runaway erections. If there is a glans ring, then I suggest the length should be about the same as your average flaccid length.
1 x
Our podcasts on Apple Podcast Store
https://podcasts.apple.com/us/podcast/m ... 1528619424
In chastity since 2013
https://malechastityjournal.com
Devoted2Her
Posts: 104
Joined: Sat Feb 09, 2019 6:47 am
Gender:

Re: My first cage. What size?

Post by Devoted2Her »

I 3d print cages and when I am setting up a custom job I tell my customer to use a sting or a piece of yarn and wrap snuggly around their scrotum and shaft (don't go so tight that you cut circulation off) mark the string and then arrange it on a piece of cardboard and use it to make a cardboard ring. Use the ring to get a feel for the ring size by trying it on for fit. Your ring should be small enough that you can only get one ball through at a time. Important, don't push your balls through the top of the ring, place the ring under your scrotum and pull your skin through, you lower hanging ball 1st and then your second ball. Wear the cardboard ring for a bit and see how it feels, you can try a slightly smaller or larder one based on comfort. You can then push your shaft through. To measure the shaft use the string to get a circumference of your flaccid shaft to get length use the string one the underside of the shaft where it meets the scrotum and got to your tip. I usually make the cage length 2/3 of that length, unless the customer requests otherwise
0 x
Post Reply