Time for a new device

For the gearheads in the audience
TwistedMister
Posts: 2566
Joined: Thu Nov 10, 2011 5:49 pm
Location: Northern New England

Re: Time for a new device

Post by TwistedMister » Sun Nov 03, 2019 5:03 am

wishful4 wrote:
Sat Nov 02, 2019 8:01 pm
I recommend the A271 or A272 depending on your size. The "arc" base ring is crazy comfortable. However, be careful from which seller you purchase. Quality can vary widely.
How does one tell the good from the bad?
0 x
04/07/19 "And then I 'punished' you by making you lick my pussy after I let my other 'boy' fuck me." --Mrs. Twisted

User avatar
wishful4
Posts: 954
Joined: Sun Oct 31, 2010 7:15 pm
Location: SE USA

Re: Time for a new device

Post by wishful4 » Tue Nov 05, 2019 12:47 pm

I was a little surprised yesterday. I recently ordered another DHGate A271 mainly to have a spare integral lock and a smaller 40MM arc ring. My spouse unlocked me yesterday so I could try the smaller ring. To my chagrin, the two pins on the cage would not go into the holes on the arc ring, not even close. The holes were drilled way wider than the pins on my cage. Guess they are all made to fit the cage that comes with them. I bought the whole device because it was cheaper than just a new ring. Guess it is going in the trash
0 x
Wishful4
Current Device: DhGate S671 (A271)
Previous devices: CB 6000s, CB 6000, MM Queen's Keep (2)MM Jailbird

User avatar
locked4her55
Posts: 2078
Joined: Sat Feb 25, 2012 10:23 pm
Location: Massachusetts, USA
Gender:

Re: Time for a new device

Post by locked4her55 » Tue Nov 05, 2019 2:11 pm

wishful4 wrote:
Tue Nov 05, 2019 12:47 pm
The holes were drilled way wider than the pins on my cage. Guess they are all made to fit the cage that comes with them.
Same with me. The cages are not interchangeable with the rings between my A271 & A273 and I purchased both devices from the same seller.
0 x
Happily secured since 4/2010 :-)
Have worn CB3000, CB6000s, MM Jail Bird & Watchful Mistress,
DHgate A271 & 273, DHgate Full Stainless Steel Belt & DHgate HT nub
Currently wearing DHgate A273

User avatar
KittensBoyToy
Posts: 650
Joined: Tue Jun 19, 2018 4:43 pm
Location: Texas Hill Country
Gender:

Re: Time for a new device

Post by KittensBoyToy » Wed Nov 06, 2019 10:27 am

The holes were drilled way wider than the pins on my cage.

If you have access to a drill press you should be able to drill new holes.
0 x
Kitten's Boy Toy
Happy to be Kitten's property!

User avatar
Tom Allen
Site Admin
Posts: 4113
Joined: Sat Sep 25, 2010 9:27 pm
Location: Southern New England, USA
Contact:

Re: Time for a new device

Post by Tom Allen » Wed Nov 06, 2019 10:44 am

Interestingly, I bought an A272, an A274, and (I think) an A273 at the same time from the same seller. The A273 was just to get one of those ball splitter base rings. However, all of them were interchangeable for me. The A272 I cut up to experiment with, and ended up making a cock ring from the cast cuff ring. The ball splitter, I discovered, looked cool, but was impractical for daily wear.

That said, I'm under the impression that there is one company doing the casting, but possibly different shops doing the machining, or possibly, a different shop from the place doing the welding. And if the pins are quite a bit different, it's also possible that somebody made a mistake, so instead of scrapping a bunch, they decided to make the cages to fit.
1 x

User avatar
Tom Allen
Site Admin
Posts: 4113
Joined: Sat Sep 25, 2010 9:27 pm
Location: Southern New England, USA
Contact:

Re: Time for a new device

Post by Tom Allen » Wed Nov 06, 2019 10:45 am

Also, the cuff ring could probably be drilled to accept the different cage pins, but you would need to carefully fixture it in a vice, surrounded by some wood, and use a decent drill bit meant for stainless. Not everybody has a drill press hanging around, although I can't imagine why. :lol:
0 x

User avatar
danj
Posts: 700
Joined: Tue Dec 07, 2010 9:41 am
Location: USA

Re: Time for a new device

Post by danj » Wed Nov 06, 2019 10:48 am

Tom Allen wrote:
Wed Nov 06, 2019 10:45 am
Also, the cuff ring could probably be drilled to accept the different cage pins, but you would need to carefully fixture it in a vice, surrounded by some wood, and use a decent drill bit meant for stainless. Not everybody has a drill press hanging around, although I can't imagine why. :lol:
No drill press here, either. But I do need to get that vice I bought like 6 months ago mounted on my workbench!
0 x
-Dan

and yes, that IS my beautiful hotwife wearing the key to my cb-6000s!

Currently Own: CB-6000s, Steelworxx Steelheart (2), modified Steelworxx Looker 3, and DH Gate A271 (2)
Currently Wearing: Looker 3

User avatar
Bird in a Cage
Posts: 214
Joined: Fri Feb 05, 2016 4:38 pm
Location: Northern Rocky Mountains (US)

Re: Time for a new device

Post by Bird in a Cage » Thu Nov 07, 2019 3:16 pm

[/quote]

No drill press here, either. But I do need to get that vice I bought like 6 months ago mounted on my workbench!
[/quote]

Take it to your father-in-law’s garage... I’m sure he wouldn’t mind helping adjust your device for his daughter’s pleasure. LOL.
2 x

Post Reply