FULL CIRCLE BACK TO HOLYTRAINER
Posted: Tue Feb 26, 2019 3:43 pm
A little background first. We started on chastity just over 5 years ago and our first expensive purchase was an HT2 which we used for some months and retained for use in "security check" areas ever since. We moved onto steel and for over four years have used various devices, mostly knock-offs through DHGate. In that time age, weight and lack of use has seen me become quite a bit smaller particularly when soft and i've had increasing difficulty with testicles escaping and with falling out of the back of devices particularly after a bath, also i've found it pretty easy to stimulate myself through the bars, so suggested we re-look at the HT range particularly the new nub model.
So as i noted on here a little while back MsM trialed a knock-off HT3 nub for a few weeks. Like a lot of knock-offs it was quite poorly made and the biggest issue was it was "warped" which made fitting and comfort while wearing difficult but it did show that i was much better contained, more secure, and had less sensation (so more frustration) when caged. So MsM ordered a "actual" HT3 nub and it arrived yesterday just a week after order with quite speedy (and tracked throughout) delivery to NZ from Switzerland.
The fit and feel is amazing, to me it feels a little like MsM has coated Her cock completely in numbing cream. The overall finish of the HT3 is very good, it has slight casting lines but nothing that needed attention and i suspect that MsM is going to be very pleased with the result. Security is way better as well as the design of the HT series with the "tube through" design making pull out, while still possible, quite difficult and certainly not something that would happen accidentally.
Overall then i'm very impressed, yes there's the downside of needing more regular removal for cleaning but actually that is an upside for me in a way as MsM will be doing the cleaning (i am not allowed to touch Her cock at all) and that's more direct teasing than i get now.
Will we go back to steel ? quite likely i suspect, but it will certainly be months, maybe years before we look at changing again.
Oh, one thing to note. When we first had the HT2 we had to get a second 40mm ring as the 45mm proved too big even though i used their measurement system. This time we knew the 40mm was a good fit so that's what we got. The best suggestion i could make to people is to order the size based on what you wear in steel or if you don't have anything to compare i would err on the side of smaller than you think. i suspect that we may move to the 36mm some time in the future but as extra rings are expensive we stuck with the tried and true for now.
Oh, second thing, V2 and V3 are not cross compatible from what i've seen.
MsM's ld
So as i noted on here a little while back MsM trialed a knock-off HT3 nub for a few weeks. Like a lot of knock-offs it was quite poorly made and the biggest issue was it was "warped" which made fitting and comfort while wearing difficult but it did show that i was much better contained, more secure, and had less sensation (so more frustration) when caged. So MsM ordered a "actual" HT3 nub and it arrived yesterday just a week after order with quite speedy (and tracked throughout) delivery to NZ from Switzerland.
The fit and feel is amazing, to me it feels a little like MsM has coated Her cock completely in numbing cream. The overall finish of the HT3 is very good, it has slight casting lines but nothing that needed attention and i suspect that MsM is going to be very pleased with the result. Security is way better as well as the design of the HT series with the "tube through" design making pull out, while still possible, quite difficult and certainly not something that would happen accidentally.
Overall then i'm very impressed, yes there's the downside of needing more regular removal for cleaning but actually that is an upside for me in a way as MsM will be doing the cleaning (i am not allowed to touch Her cock at all) and that's more direct teasing than i get now.
Will we go back to steel ? quite likely i suspect, but it will certainly be months, maybe years before we look at changing again.
Oh, one thing to note. When we first had the HT2 we had to get a second 40mm ring as the 45mm proved too big even though i used their measurement system. This time we knew the 40mm was a good fit so that's what we got. The best suggestion i could make to people is to order the size based on what you wear in steel or if you don't have anything to compare i would err on the side of smaller than you think. i suspect that we may move to the 36mm some time in the future but as extra rings are expensive we stuck with the tried and true for now.
Oh, second thing, V2 and V3 are not cross compatible from what i've seen.
MsM's ld