"Attica chastity cage"

m_gameboy · Post by **m_gameboy** » Sat Nov 12, 2011 6:42 am

Sax Leather in Australia has just come out with a cage device called the Attica chastity cage. Photo attached. It apparently comes with a 45mm or 50mm hinged ring, and the cage has an internal diameter of 35mm (1.25inches) and is approx. 65mm (2.25inchces) long.

Has anyone seen this, or heard of it before? Is it perhaps another brand "rebadged"?

m_gameboy

(Male chastity - you could say it's for those who focus on the journey, not the destination)

McAndrew · Post by **McAndrew** » Sat Nov 12, 2011 7:15 am

It's Chinese, but actually good quality.
That's it on my avatar. (Slightly modified)

I posted about it in the 'Device Recommendation for New Users' topic.

Atone · Post by **Atone** » Sat Nov 12, 2011 9:19 am

I don't know anything about this device but just so you know

35mm is actually about 1 3/8" (1.38")
65mm is a little over 2 1/2" (2.56")

Not sure if those specs came from the website or your conversion but I am always suspect when things like this don't match up.

Also, for the base rings

50mm is 1.97" or about the size of the largest ring on a CB Series
45mm is 1.77" or about the size of the middle ring on a CB Series (I think)

If you know those are good sizes (like if you already had a CB Series) this may be an ok choice. If not then you may want to try getting a cockring that size first and trying it out. I don't have numbers to back this up but just from my reading it seems that very few people end up in the largest ring on a CB but few can start with the middle ring either but many end up there. This combination may not get you there without a lot of frustration along the way. I guess this just leads me to the other post about best device recommendation for new users http://chastityforums.com/viewtopic.php?f=3&t=11000

-A

ptharv · Post by **ptharv** » Sat Dec 03, 2011 10:42 am

Had it and wore it for several months. Very high quality but also found a low quality version that was not nearly as well made or as well finished. My version also had the penis plug with a 6mm diameter. The only problem was the hinged cock ring. The rubber cover became very uncomfortable but was even worse without it. Ended up going to the steelheart. It also looks like this is the short version which is the one i had. It.is very small and short. I started with medium cock ring but ended up with a smaller...1 1/2 inch.

Post by **thumper** » Sat Dec 03, 2011 4:01 pm

ptharv wrote:The only problem was the hinged cock ring. The rubber cover became very uncomfortable but was even worse without it.

That seems to be the universal experience with that kind of thing. At least for those interested in long-term wear.

McAndrew · Post by **McAndrew** » Mon Dec 05, 2011 3:52 pm

ptharv wrote: The only problem was the hinged cock ring. The rubber cover became very uncomfortable but was even worse without it.

It not obvious in my avatar, but I coated the ring with clear heat-shrink. This not only covers the hinge and makes the edges softer, but also stops any movement and pinching at the top joint.

hubby2nd · Post by **hubby2nd** » Sat Jan 05, 2013 7:33 am

McAndrew wrote:
ptharv wrote: The only problem was the hinged cock ring. The rubber cover became very uncomfortable but was even worse without it.
It not obvious in my avatar, but I coated the ring with clear heat-shrink. This not only covers the hinge and makes the edges softer, but also stops any movement and pinching at the top joint.

I'm getting an Attica from uberkinky and like your idea regarding the heat-shrink. What size did you use? And any tips for application appreciated from this experienced diy'er (but not for much longer!)

luckylocked · Post by **luckylocked** » Sun Jan 06, 2013 5:42 pm

I have the San Quentin that I also got from Sax Leather. Build quality is very good, but the rubber on the hinge does take some getting used to. You can't really wear it without as there is the slightest gap that can grab your scrotum. It also has some weight behind it but I got used to that fairly quickly. I much prefer it over my CB6000S.

The heat shrink idea could be the go. I may well try that, although I am going to get a MM JailBird soon.
If you can be bothered to wait, I am pretty sure Sax get them from DH Gate where they are $40AU but can take 5 weeks for delivery.

http://www.dhgate.com/small-stainless-s ... #s1-2-null

hubby2nd · Post by **hubby2nd** » Sun Jan 06, 2013 7:02 pm

Can I ask what's made you go for the San Quentin over the Attica? I thought the Attica was closer to the job in design?

hubby2nd · Post by **hubby2nd** » Mon Jan 07, 2013 6:08 am

Let me try that again! I thought the Attica was closer in shape to the jb, as the San Quentin appeared to hold you down and in close?

Chastity Forums

"Attica chastity cage"

"Attica chastity cage"

Re: "Attica chastity cage"

Re: "Attica chastity cage"

Re: "Attica chastity cage"

Re: "Attica chastity cage"

Re: "Attica chastity cage"

Re: "Attica chastity cage"

Re: "Attica chastity cage"

Re: "Attica chastity cage"

Re: "Attica chastity cage"