Wrench-holder? :)

Living the real life under lock and key

Wrench-holder? :)

Postby Finn » Sat Jul 22, 2017 10:19 am

I've made a number of mods to my CB6000, to make it work longer term for me, and my keyholder. My main problems have been stealth under clothes, and the balance between comfort, and my right testicle pulling through the ring.

My solution to the problems has been to mess with the design a bit. I bought the 2nd largest accessory ring, as I am (or was, before all this!) fairly large. Then I had to figure a way to keep my nuts from pulling back through. First I shortened up the spacers. This ran out of adjustment, so I switched things around. I put the cage flush with the ring, and used the spacer on the outside, (after shortening it) so the lock applied enough pressure to keep everything from sliding about. This worked decently, but it had more free-play than I like, and I occasionally got pinched. It also still made more of a pants bulge than I like in public.

Step two has been to replace the pin/spacer/lock, with a nut and bolt. Running a small bolt in the same position as the pin, I have less than 1/4" of thread protruding. A small washer and nut tighten down, and remove all free play. Now I have the cage, sitting against the base ring. I've shortened the 2 side locating pins, so they don't stick out. By going oversize on the base ring (5 1/4?) I don't get the shaft chafing I was getting, especially at night, but with the cage flush to the ring, there isn't enough room for my balls to yank through, and they are comfortable when relaxed. I've has 2 pull throughs, sitting on a cold toilet, but that's really rare. I had been going finger tight with the nut, but found that if it got loose, it would pinch the top of my dick like a lobster. The solution is to use a small 3/8 wrench to tighten it up snug.

Now it sits tighter to my body. It's got no lock and pins protruding, so it's more stealthy. My balls don't need the smaller ring to keep from pulling through. The downside is that my keyholder is likely swapping her key (for this cage anyhow) for a pocket sized wrench. there is actually something really sexy about being bolted into a device, I have to say.
Living with my 2 favorite people, in a semi-poly situation. Serving my Mistress Crosby, who holds my keys.
Finn
 
Posts: 320
Joined: Thu Aug 09, 2012 9:22 am
Location: Ontario, Canada

Re: Wrench-holder? :)

Postby happilylockedman » Sat Jul 22, 2017 11:01 am

Very creative. You could go a step further. Welding. Your Lady would go from key holder to wrench holder to torch holder. What do you think?????????? :D
happilylockedman
 
Posts: 59
Joined: Fri May 12, 2017 3:32 pm
Location: South West Connecticut

Re: Wrench-holder? :)

Postby Finn » Sun Jul 23, 2017 1:06 am

happilylockedman wrote:Very creative. You could go a step further. Welding. Your Lady would go from key holder to wrench holder to torch holder. What do you think?????????? :D


Well, it's a plastic CB, so that wouldn't work! There are still times I need to take the cage off. I sometimes go a few days locked in a row, but I can't manage more than that due to life, and sometimes discomfort getting in the way. Part of the deal is that I'm chaste, even when unlocked, so it's OK to be free now and then!
Living with my 2 favorite people, in a semi-poly situation. Serving my Mistress Crosby, who holds my keys.
Finn
 
Posts: 320
Joined: Thu Aug 09, 2012 9:22 am
Location: Ontario, Canada

Re: Wrench-holder? :)

Postby Tom Allen » Sun Jul 23, 2017 9:03 am

A long time ago, there was a period when we were traveling, so I used a nylon bolt and nut arrangement, with a hole drilled through the side so we could use a numbered tag. But eventually we got too worried about any type of detector noticing g the device so we do no t travel with one anymore.
User avatar
Tom Allen
Site Admin
 
Posts: 3324
Joined: Sat Sep 25, 2010 9:27 pm
Location: Southern New England, USA


Return to General Chastity Chat

Who is online

Users browsing this forum: No registered users and 6 guests